Lomo camera manual

Camera parts and main controls are given In Pic. Installing and Checking the Cells. To install the power source into the camera, move cover 16 Pic. Close the container cover. Watch attentively over correct setting of the cells. The cells installed, check them for serviceability. For this aim, move curtains control key 14 so as is shown in Fig. Open the viewfinder. Looking through the inspection window 23 Pic.

If the cells are serviceable and inserted in a correct way, a red-color indicator should shine at the upper left corner of the viewfinder Pic. To check up energetic level of power cells in the course of taking, press down the release knob. Camera Loading. Camera LC-A is rated for mm perforated film loaded in a standard cassette. To insert the cassette with film into the camera, swing out knob 25 Pic.

Put the cassette into receptacle 27 so that a film leader is facing to the right. Lower hand wheel 24 so that yoke 26 enters the cassette spool lug. Put the film leader Pic. Holding the cassette with film with your hand and rotating hand wheel 22 with the other hand, take up film slack. Make sure the film is positioned between limiters 28, that it is engaged with gear 29 and is fixed reliably at take-up spool If hand wheel 22 has turned up to stop while the film slack has not yet taken up, press down release knob 10 Pic.

If the objective and view-finder are covered with the guard curtains, release knob 10 is interlocked. Never press the release knob when the guard curtains are shut. To unlock it, apply key 14 Pic. After the slack is taken up, close camera back 32 Pic.

Turn hand wheel 22 Pic. While pulling the film, watch rewind hand wheel 24 Pic. If the camera is loaded with the film correctly, hand wheel 24 should rotate at rotation of hand wheel Setting Value of Film Light Sensitivity. After installing the cassette with film into the camera, it is required to introduce into the exposure meter a value of light sensitivity of film applied the value given on the packing.

For this aim rotate film light sensitivity setting knob 6 Pic. Falls du ein wenig von der Filmlasche aus der Kapsel herausstehen lassen willst z. Falls die Linse schmutzig oder fettig wird, sollten. Eh oui! Le LOMO est de retour! Une parfaite. Si elle ne tourne pas, tu ne prends pas vraiment de photos et il faut recommencer le chargement de la pellicule.

Vous pourrez sur- ou sous-exposer vos images en choisissant simplement une vitesse de pellicule qui soit un ou deux diaphs plus rapide ou plus lent e que celle que vous. Un autofocus, par exemple,. Et tu verras. Glisse solidement ton flash dans le Sabot Flash [19].

Garde un. Deben de ocupar su espacio de forma apretada y en fila india. La lamparita a la izquierda en el visor indica el control de las pilas [3] y debe de dar una luz roja. Si no se ilumina debes de comprobar si has colocado bien.

Es el momento de sustituir tus viejas pilas por unas nuevas. No te olvides que tanto el disparador. Primero, abre la tapa trasera [4] accionando hacia arriba la manivela [5] como hemos indicado anteriormente.

Utiliza tu dedo y gira la ruedecita hasta que la sensibilidad adecuada , , , y aparezca por el ventanuco rectangular. El enfoque es manual, accionando la palanca [17] a la derecha de la lente [10] y seleccionado la distancia deseada. Es muy simple y sin tan siquiera mirar: coloca con el.

Baja un poco la palanca si quieres un plano medio 1,5m. Sigue bajando para una distancia de 3m y si quieres lomografiar al infinito, baja hasta el tope inferior: 3m hasta infinito. Solo necesitas practicar un par de veces con el dedo. Arriba: primer plano, abajo: infinito, el centro: un plano medio. Pero todo cambia cuando las condiciones de luz son bajas. Adora especialmente el espectacular Colorsplash Flash. Ajusta el flash directamente en la zapata [19]. Cuando el obturador cierra y se escucha.

Con el Colorsplash Flash puedes utilizar tranquilamente. Estate atento y. Evita tanto las temperaturas muy altas o muy bajas. La lente debe de protegerse de objetos cortantes.

No introducir los dedos. Sappiamo, che non puoi aspettare e che vuoi finalmente un assaggio del nuovo gioiellino che hai tra le mani. Attenzione, eccola! Saluti da San Pietroburgo. Guarda nel mirino e premi dolcemente il pulsante di scatto [2], per vedere se effettivamente le pile funzionano. Se la spia non si accende, dovresti controllare se le.

Entrambe le parti sono poste sulla parte superiore sinistra della macchina fotografica, impugnando la macchina per scattare una foto. Poni ora la macchina fotografica di fronte a te. In questo caso devi sostituire le pile. We embrace opportunities to collaborate with inspiring international artists and have an array of limited edition designs.

Our Instant Cameras are often released boasting brand new outfits, looking fierce, fresh and funky. HuiXingDao Island is a Weibo photography aesthetics blogger. He tested out the Lomo'Instant Automat Glass and created some timeless snapshots of his life through a viewfinder.

Chase the gloom away with these cheerful outdoor shots taken with the Lomo'Instant! Tattoos may be the only imprint that can be voluntarily recorded on one's body, condensed from an experience into a pattern, the meaning behind it may only be understood by the owner of the body and the hands that gave birth to it.

We invited Mirmanda, a Hong Kong tattoo artist to share her story, stay tuned! Community member Dani aka candeeland, tells us why her Lomo'Instant Wide and Close-up Attachment combo is her go-to kit when she wants to shoot flowers and plants up close. We invited Taiwanese illustrator Ming to record his trip to the south last summer with Lomo'Instant Wide and had him sharing his list of coffee shops around the world.

There are many different techniques to do light painting, and in this interview we will discover how photographer Maria Saggese — a master of this art — bends light at her will. This is the perfect mode for shooting all hours of the day and night!

If you want to expose longer than 30 seconds, you may use the multiple exposure function to expose the same film multiple times to accumulate exposure time.

When your film is properly installed and you have selected your shooting mode, you are ready to shoot.